What are max print speed and volumetric set to?
For some filaments (silk PLA) I’ve had to slow things down (120mm/s max print speed and 10mm3/s max volumetric speed) or it comes out horrible. Only used 0.4 nozzles so far though.
What are max print speed and volumetric set to?
For some filaments (silk PLA) I’ve had to slow things down (120mm/s max print speed and 10mm3/s max volumetric speed) or it comes out horrible. Only used 0.4 nozzles so far though.
Star Trek ENT season 4 episode 10 “Daedalus” has the transporter inventor on board for an experiment. I’d like to see more about initial development too.
Slicers for FDM are open source and lots of forks. The built-in printer profiles vary a lot but can be created from scratch. You can find lots online to use as examples too. I currently use Cura, Prusaslicer, and Orcaslicer.
I’m more interested in printing plastic than tuning/upgrading the printer itself so I recommend a printer with automatic z-offset and bed leveling. Basic maintenance tasks such as cleaning, oiling, and greasing will need to be done on occasion no matter the printer. Beyond that I’ve only done simple retraction tuning.
I started with Elegoo Neptune 3 Pro. Klipper firmware upgrade improved speeds a lot. It wasn’t bad for a budget printer but lack of automatic z-offset can be frustrating so I replaced & gave it away to friend. Replaced it with Creality K1 which was a lot easier to get started with thanks to automatic z-offset calibration. Output quality is good but to get better would require upgrades + tuning. Been saving up to replace with Bambu Lab P1S combo so I can also do multi-color printing.
I’d recommend using distro you know best and/or most prefer to work with. I use the flatpak install of Jellyfin Media Player but there are also deb files available.
I’m currently using minipc with Intel n5105 (or something similar) for 1080p HTPC. Debian 12 OS with auto-login & Jellyfin Media Player starting at login. I control it with pepper jobs RF remote but also have a logitech wireless keyboard+touchpad for it. Keyboard+touchpad come in handy when browsing media sites on firefox but some might restrict quality. Some of the newer minipc’s I tried required adding backports repo to install newer kernel for wifi to work. I had been playing with Debian a lot when I set up first one & been using clonezilla to image them so it’s stuck.
Ordered a gmtek n97 minipc to play with and should have it in about a week. Going to test it out with 4k but it’s not a deal breaker for me if it cannot handle that well enough.
Yep, asking for something I’m sure a lot of us would love to have, a ready to go TV remote control style usage, but rather than having discussions about why those options aren’t viable just downvoting.
Create a backup image from the working SD card. Write that backup image to a spare SD card and verify it works. Then try to do ‘apt update’ and see if anything breaks. If it breaks you got a spare SD card ready to go :)
I had issues with DNS checks and traced it to my pihole. I changed that container’s resolv.conf to use cloudflare DNS and it has been working fine since. It was with Caddy so needed to change over to use IPs.
Sometimes I’ll lower resolution or quality just so a game loads quicker.
Another thing to remember is the client needs to support decoding the video in hardware or have enough CPU to handle it in software. I have intel i7 (3rd gen) with no hardware HEVC/x265 support but it has enough CPU to power through.
Self-host your own ACME server. Then you can use certbot pointed there.
These instructions are old so not sure if newer/better ways, https://blog.sean-wright.com/self-host-acme-server/
Is MariaDB on spinning disk or ssd?
I initially set up Nextcloud with MariaDB on spinning disk but it was slow even completely empty. I moved that container to ssd & performance was a lot better. The web UI may still have some slow loading parts but I can’t say for sure since rarely use it. Caldav+carddav+Nextcloud client are how I usually interact with it.
Sounds like bridge mode is needed for the vm’s network interface in virt.
I would say proxmox ve is easier to start with.
The container method used should be whatever you are more familiar with or prefer. They both have their own quirks, pros, & cons.
SELinux - If you don’t want to deal with SELinux then set it to permissive mode. If you want to keep in enforcing mode you need to create the appropriate policies, https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/8/html/using_selinux/configuring-selinux-for-applications-and-services-with-non-standard-configurations_using-selinux
Firewall - If you don’t want it’s protection then look up instructions to stop & disable it on your distro.
Port forwarding - From linux container side you either need to specify host networking or the ports you want to allow through, there is no avoiding that if it needs to be network accessible. If you want it internet accessible then you need to setup port forwarding on your router.
Have you looked into something like yunohost? It may be the kind of thing you’re looking for.
If router supports it, a static route via connected machine with IP forwarding enabled might work. OpenWrt has packages for things like tailscale and zerotier so could do it without an extra machine too.
For 3, if router supports it could also try doing static route via Tailscale joined machine that has IP forwarding enabled
If your router lets you try adding a static route for the tailscale IP/subnet to the laptop with IP forwarding enabled.
Refunds came about because of EU laws. Those flash sales would have resulted in a bunch of refunds so they stopped doing them at the same time. They actively encouraged (and still do) people to refund & rebuy for cheaper at any time whether any steam sale is involved or not as long as within the refund terms.
Personally, I only miss the mini games they had during those sales but I hated the flash sales themselves. Had to waste time researching when the games wanted were going to be the cheapest during the flash sale. Then had to hope it was during some free point of the day, notification/alarm worked, or that didn’t forget to create the notification/alarm. Then had to hope the store wasn’t overloaded because everyone else was also trying to get in on time limited sales.
Was it the official container image or 3rd party? Whichever it was, they should get notified so that init script can get fixed to prevent similar happening to others.
Would love a new Steam Machine and could actually be good this time. Proton didn’t exist when they released the original Steam Machines which limited you to linux ports of games. I had bought two but wiped & did clean installs of Windows 7 so we could play all the games wanted to.
Before Proton, gaming on linux relied on native ports or WINE. Native ports were rare & not always better. WINE took some learning to make work well but I dunno, never got any good at it.
My first zigbee device was Sylvania (73685) rgbw led strip. On it’s own it worked fine but once I started trying to add sengled zigbee bulbs I kept having problems with pairing the bulbs or keeping them connected. Zigbee uses 2.4ghz so I thought maybe interference so lowered power output on wifi AP 2.4ghz band & even turned it off for testing but didn’t help. I think I read somewhere that sylvanias caused that problem. I unplugged sylvania led strip, reset & rejoined everything else and had zero problems. Tried to add the sylvania back in and disconnect problems came back after awhile. It was past the return period so now I keep it unjoined and plugged into a zigbee smart outlet. I sometimes have to remove power from it to join new devices or when I restart zigbee controller. Currently have mix of sengled bulbs, thirdreality plugs, sonoff plugs & sensors, and single aqara tvoc all working together fairly reliably.