I don’t own Prusas but I migrated from super slicer to prusaslicer and being able to cut models and add locating pegs easily is such a game changer for larger parts
I don’t own Prusas but I migrated from super slicer to prusaslicer and being able to cut models and add locating pegs easily is such a game changer for larger parts
Be careful depending on the model, some of those run hot. I managed to kill one in under 2 weeks just by copying a large amount of data to it and had to print a fan shroud for it’s replacement to keep the temps at a reasonable level.
JetBrains IDEs for me
I don’t do it and we have no expectation of it. A good portion of our infrastructure is self healing and spread across multiple zones which has been enough for us for the past 10 years. The parts that aren’t can wait until business hours and clients are aware no work is done outside of them so any fixes or changes wait until the following business day.
You would have to more than double my salary to get me onboard with structuring my personal life around “but what if there’s an outage”, and even then I probably wouldn’t do it lol
Heavily agree, a lot of content had issues playing for me with swiftfin. No issues at all with Infuse other than the fact that intro skipper doesn’t work with it
Wow he must’ve struck a nerve with you to get this reply
Yep and reddit is slowly closing themselves off, I wouldn’t doubt you eventually have to be logged in to even view anything.
Forums are still around but it’s usually just the older established ones (I’m on stangnet.com and corral.net regularly but they’re car related so lots of technical info). Everything new either went Reddit or Discord it feels like and I’ll never install Discord.
I think Jellyfin started a forum post reddit but I haven’t gone looking yet for that one.
Information is absolutely getting harder to find online and if archive.org goes down we’re really screwed
I don’t think your particular case would have any creep as it’s not mechanically leveraged in any real way.
If you were to print something like a cupholder for a stroller or bike where it’s holding something up with some weight while in the heat is where you would notice it especially with repeated impact. Most likely wouldn’t outright fail but under constant load you would notice it starting to bend a little. That said you can absolutely over engineer it to prevent that rather than switching materials which can be a huge pain depending on the printer.
I did my hydroponic tower in PETG but it honestly would’ve been ok in PLA since it’s just a static fixture. I’ve had a PLA badge on my car for 3 years in 110+ summers and similar to you I’ve only noticed fading on the raised white lettering.
My money’s on them selling PS2 demo discs
JetBrains did similar with their perpetual fallback license and it did ok. My only gripe with their strategy was it required either the upfront year paid or at the end of 12 months of month to month you would get the license. Issue was the license was from the first month so you would have to go downgrade. I like your idea way more
Typically using Lando which is a frontend for docker-compose which makes it easier for the users unfamiliar with docker to use it to spin up their environments.
I’ve got 3 Wyze cam v3s running the wyze mini hacks firmware sectioned off in a VLAN that can only reach Frigate (no internet).
I have frigate running on a cheap Lenovo M900 I got on ebay for $65 that has an i7 and 8gb of memory and it actually does fairly well without the Google coral USB TPU as long as that was the only service on that system. Trying to run Frigate on my NUC with other services without a TPU caused some issues with CPU usage but with a TPU I would bet it’ll all run on the one system.
Home assistant works exceptionally well for notifying, one of my cameras I have on UDP since the signal isn’t great and get a couple artifacts that trip it up but other than that it has been much quicker to notify and more reliable than anything in the consumer market I’ve tried so far.
I’m on the 5A now and my wife has a 7, her 7 has the screen randomly freak out where you can’t even turn it on or reset (holding power will make it vibrate after about a second preventing the hold to reset). Just have to mess with it until you can get in and hit restart then it’s fine for another week or two usually.
The 5A is fantastic until it abruptly dies which has happened to me twice now (both times while sitting with it in my hand). If they didn’t have screen and motherboard issues I would absolutely run this phone into the ground since it’s a great experience with GrapheneOS, has a headphones jack, and has the rear facing fingerprint sensor.
I can’t speak to the 6 but I know some people didn’t like them after the 5 since it switched to tensor
I used gpt4 for terraform and it was kind of all over the place in terms of fully deprecated methods. It felt like a nice jumping off point but honestly probably would’ve been less work to just write it up from the docs in the first place.
I can definitely see how it could help someone fumble through it and come up with something working without knowing what to look for though.
Was also having weird issues with it truncating outputs and needing to split it, but even telling it to split would cause it to kind of stall.
I just used a buck converter and a USB pigtail for mine so it still plugs into the pi where the power cable used to it’s just running off the Ender 3s power supply. They were fairly cheap on Amazon something like $6 for a pack
The only cables you really see for my printer are the short USB connecting the Pi to the SKR on the back, and the power supply cable. The rest is hidden or inside cable chains.
Definitely made moving the printer easier and much less of an eyesore of wiring.
This isn’t far off from where I print PETG with a stainless nozzle for 125mm/s. If you’re using a brass nozzle and not pushing speeds then it seems high.
Have you PID tuned it?
Oh yeah definitely commissions are a whole other ball game they should at least pay for the filament needed to R&D it and ideally do something for your time
I never bothered with it but I’m sure you could. I just public domain everything I design since it’s a lot of older automotive stuff and I’d rather it be readily available.
Yep I only use Instagram and the fighting in comments of reels is extremely prevalent.
Content creators will even intentionally misspell things to try to kick it off if it’s a reel where the intention is to insult someone else.
This is pretty great advice to get into it. I previously ran 3 poweredge 2950s but have since switched to nothing self hosted and back to everything self hosted but on a much leaner setup with a NUC and 14tb WD my book drive with a dual Noctua 4020 fan shroud I 3d printed that it absolutely needed as I killed the original drive in two weeks.
My replica is just a 14tb in my desktop I run rsync to pull the data occasionally after checking SMART status on the primary. It’s not versioned or perfect but it works great to give me a chance to backup my jellyfin media. Everything I care about also gets backed up via restic.
Eventually plan to run a build with the Modcase MASS with multiple drives but for now this setup has been working fantastic.